How to Make a Beautiful Macrame Hammock Chair

Prev1 of 2
Click Next Page ( Page # ) to Continue Reading !

Sometimes, relaxing on the porch requires a comfortable and stylish hammock. With a few tools and some basic math skills, you’ll have a beautiful chair that shows off your do-it-yourself skills. This hammock is made using the macrame technique, which requires knotting together cords. Macrame is a centuries-old method used to make furniture, plant holders and other home decor items.

Relax on your porch in a comfortable macrame hammock.

(Angie Diersman)

Sponsored Links

  • 3 1 1/4-inch hardwood dowels, 30-inches long
  • 2 5/8-inch hardwood dowels, 36-inches long
  • 200 yards, 1/4-inch macrame cord or rope
  • 8 yards, 1/2-inch rope
  • 4 1-inch wood screws
  • Drill and 5/8-inch bit
  • Measuring tape
  • Scissors
Supplies to make a macrame hanging chair.

Angie Diersman

While measuring and drilling the dowels, ensure all the holes are level and lined up with each other so that the frame is perfectly square. On two of the 1 1/4-inch dowels, measure and mark at 2 inches and 3 1/2 inches from each end. The third 1 1/4-inch dowel will only need to be marked at 3 1/2 inches from each end.

Measure and mark the dowels for drilling.

Angie Diersman

Drill a hole at each mark on each 1 1/4-inch dowel. Start with a small drill bit and work your way up to 5/8 inch. A spade bit or dowel jig makes this much easier.

Drill holes in dowels using a spade bit or dowel jig.

Angie Diersman

Sand the holes to remove any splinters from drilling.

Sand holes to remove any splinters.

Angie Diersman

Make a square frame for the seat by sliding each of the small dowels into the 5/8-inch holes on the large dowels. Leave about 1-inch overlap on each end.

Slide dowels together to create a square frame.

Angie Diersman

Drill a small pilot hole where the dowels meet. Using a 1-inch screw, secure the two pieces together.

Screw together the two dowels to secure the frame.

Angie Diersman

Before starting the macrame, temporarily hang the frame in a place where you can easily stand or sit to knot the ropes.

Temporarily hang frame for easy use.

Angie Diersman

Using the 1/4-inch cord, cut 16 26-foot pieces. It sounds like a lot but as you knot, the cord shortens quickly. Pick up one cord and fold it in half. Wrap the loop around the dowel from the front to back. Pull the tails through the loop. Continue with all 16 strands of cord. Once they’re all hanging, you’ll have 32 strands.

Wrap the loop around the dowel and pull the tails through.

Angie Diersman

To create the seat, you’ll be using a simple square knot. Starting with the first four cords, take the left cord and cross it over the center two, then under the right cord.

Four cords are used to create a square knot.

Angie Diersman

Take the right cord and cross it under the center two cords and up through the hole, passing over the left cord.

Change the direction by crossing the cords from right to left.

Angie Diersman

To complete the second half of the knot, you’ll do the same thing in reverse. Take the right cord and cross it over the center two, then under the left cord. Then take the left cord and cross it under the center two cords and up through the hole, passing over the right cord. Pull the knot tight. Continue this with all the cords.

Pull the knot tight and continue with all the cords.

Angie Diersman

The next row also uses the same square knot but starts with the third cord. You’ll be using two strands from each section. When knotting them together, make sure to keep everything even. Continue this until to reach the end of your cords.

Use two strands of cord from each section.

Angie Diersman

Now the pattern repeats. Just like in the beginning, tie a square knot with the first four cords and work your way across. Then use the third cord to start the next row.

Continue using square knots to create the seat pattern.

Angie Diersman

Continue knotting until the seat is about 45-inches long. The finished macrame needs to be longer than the frame.

The seat needs to be longer than the frame so it hangs loosely.

Angie Diersman

To attach the ends to the bottom of the frame, wrap all four cords from each section around the dowel and tie a knot.

Wrap the cords around the dowel and tie a knot.

Angie Diersman

Tie a second knot by splitting the strand into two. Pull it as tight as you can.

Tie a second knot to secure the cords to the frame.

Angie Diersman

Cut the ends of the cords to the length desired. You can fray the ends or leave them as is.

 

Cut the ends of the cords to the length desired.

Angie Diersman

Prev1 of 2
Click Next Page ( Page # ) to Continue Reading !

Loading...