Removable Door Paneling

  • removable door paneling, doors, wall decor
BEFORE:
This is the guest room closet door in my pastor and his wife’s house. It’s plain and simple with not a lot of character.
  • removable door paneling, doors, wall decor
SUPPLIES:
-4 pieces of 3/8 in. x 1-1/4 in. x 8 ft. Basswood Panel Moulding
-Behr Marquee Color Sample size of Ultra Pure White interior/exterior semi-gloss paint
-1” Wooster Pro angled paint brush
-measuring tape (Stanley Powerlock 16’)
-fine grit sand paper
-350” roll of Scotch Indoor Mounting Tape
-180 grit (x-fine) 3M Pro Grade Dual Angle Sanding Sponge (optional)
-DAP Plastic Wood-X All Purpose Wood Filler
Not pictured:
-DeWalt miter saw
*NOTE: I ended up returning the Minwax Wood Filler as it’s a two-part filler and I didn’t need something so complex. I replaced it with something much less expensive and easy to use: DAP Plastic Wood-X All Purpose Wood Filler. This stuff dries quick and reminds me a lot of spackling.
  • removable door paneling, doors, wall decor
STEP 1: Cut Moulding
For this step, if you don’t have power tools, you can ask someone at the hardware department store (Lowe’s and Home Depot will do this as far as I know…not sure about any other place) to cut your moulding for you.
Another option would be to purchase a miter box with a saw (here’s a link to one at Home Depot: http://www.homedepot.com/p/Stanley-Deluxe-Miter-Box-with-Saw-20-600D/100034395).
Whether you’re using a miter saw or miter box and saw, you’ll want to cut the ends of your moulding at a 45* angle.
  • removable door paneling, doors, wall decor
Something else to keep in mind is which way you’re making your cuts. Make sure that you’re paying attention to the design of the moulding and making your cuts so that they all are the same. For example, I made the mistake THREE TIMES of having the concave/divot side of the moulding being positioned on the outside edge of my final panel box rather than on the inner edge of the box. Basically, once I put my “boxes” together after all of my moulding was cut, three of my four sides didn’t look continuous. Make sense?
  • removable door paneling, doors, wall decor
Once I made my first 45* angle cut on the very end of my moulding, I flipped it over and measured from the pointy edge to where I needed the other end to be, then made my mark and cut.
  • removable door paneling, doors, wall decor
Here are my cuts all laid out (again, a few of these had to be re-cut because of the design but you may not even be able to tell from the photo).
For a 24″x80″ door, I ended up with:
(2) 34″ pieces
(2) 20″ pieces
(6) 16″ pieces
(2) 6″ pieces
  • removable door paneling, doors, wall decor
STEP 2: Paint moulding
After all of my pieces were cut, I painted them white (if you want to get funky and do a different color, I’d love to see what you come up with!). I just did one coat on the front, back and edges.
  • removable door paneling, doors, wall decor
STEP 3: Sand moulding
Next, I lightly sanded the edges where I cut in order to get rid of splinters and make the edges smooth.
  • removable door paneling, doors, wall decor
STEP 4: Measure center and adhere moulding
Finally, it was time to do the fun part! I found the center of the door and measured down 4″ (all measurements will vary based on the size door you’re working with). If you want to go a step further, you can use painter’s tape to get all of your moulding aligned but I just eyeballed everything.
  • removable door paneling, doors, wall decor
After I made a tiny mark at 4″, I used small strips of my double-sided tape and adhered them to the back of each strip of moulding. The tape I used gives a warning that it is permanent and may damage the surface if removed, but I was able to reposition the moulding even after I stuck them to the door. I would advise, however, not to completely press them down until you’re happy with their positioning–this way you’re less likely to mess up your door while you’re working out alignment.
Once you have your tape on the back of your moulding, adhere it to the door.
  • removable door paneling, doors, wall decor
After I had my first “box” on the door, I measured down 4″ and created my next box. I repeated this a third time, creating three panel boxes in total.
  • removable door paneling, doors, wall decor
STEP 5: Fill cracks, sand and paint
After my boxes were assembled on the door, I used my finger to wipe on wood filler in the joints of the moulding. I’m sure there’s a tool for this but I found that I could get into the crevices and smooth out the wood filler easier by using my finger.
Try not to get too messy with this step–maybe even keep a rag on you so you can quickly wipe off any excess wood filler as you work–this stuff dries quick!
Once you’ve filled in the joints, take an angled sand sponge (or just a regular piece of extra fine sandpaper) and lightly sand away any dried excess wood filler.
  • removable door paneling, doors, wall decor
Lastly, apply a second coat of paint over all of your moulding, paying attention to the joints. You want your panel boxes to look as if they are one completed piece.
  • removable door paneling, doors, wall decor
I was so amazed at how easy this project was and the fact that it cost me roughly $60 to create this look versus going out and spending about $160 on a door that would look very similar in design. I figure for a bedroom door to go from plain to pizazz, that’s not half bad!
  • removable door paneling, doors, wall decor
Here is a split screen shot so it’s easier to see the before and after. I realize the alignment isn’t PERFECT but for a quick facelift, I’m happy with it. ?

Materials I used for this project:

  • 4 pieces of 3/8 in. x 1-1/4 in. x 8 ft. Basswood Panel Moulding   (Home Depot)
  • DAP Plastic Wood-X All Purpose Wood Filler   (Home Depot)
  • Behr Marquee Color Sample size of Ultra Pure White interior/exterior semi-gloss paint   (Home Depot)
  • 1” Wooster Pro angled paint brush   (Home Depot)
  • Measuring tape (Stanley Powerlock 16’)   (on hand)
  • Fine grit sand paper   (on hand)
  • 350” roll of Scotch Indoor Mounting Tape   (Home Depot)
  • 180 grit (x-fine) 3M Pro Grade Dual Angle Sanding Sponge   (Home Depot)
  • DeWalt miter saw   (on hand)

Loading...